integrated micro insert vial Aijiren pump

Pump Parts for Aijiren® 33 results (1 filter applied, reset) close. Filter. PM Kit, & Pumps, Comparable to OEM # G1310-68741. Sciencix Part #: 11-4147

Aijiren II LC system - SRA InstrumentsReliable instrumentation combines with latest column technologies and advanced supplies to guarantee robust separation and dete Email: market@aijirenvial.com

8 Binary Pump VL User Manual 1 Introduction Introduction to the Binary Pump Introduction to the Binary Pump The binary pump comprises two identical pumps integrated into one housing. It provides gradient generation byhigh-pressure mixing. Degassing is not included but a vacuum degasser is available as a separate product for

EssentialThe Aijiren Bio-inert Quaternary LC features bio-inertness for all components without exception. Bio-inert High Performance Autosampler Parts Descript Tel: +8618057059123

Regular Price $8.51 Price $7.40. Add to Cart. Screw Top 9mm Plastic Clear 0.3mL HPLC Autosampler Vials w/ Micro-Insert - 100/pk, CV1981. Regular Price $10.83 Price $9.42. Add to Cart. Crimp Top 11mm Amber Glass 1.5mL HPLC Autosampler Vials w/ Writing Patch - 100/pk, CV1929. Regular Price $8.10 Price $7.04. Add to Cart.

Aijiren premium certified vials, ca. Tel: +8618057059123 2021/7/8 · Certified 0.2ml micro insert vial manufacturer Aijiren Wholesales 150ul hplc insert supplier ...

The II Vialsampler combines sample management and column handling in a single autosampler module. The Vialsampler injects from up to 132 standard 2 mL vials and has a pressure rating of 600 or 800 bar. Options and upgrades are available for sample cooling and heating from 4 to 40 °C.

1.5mL Clear Screw Neck Vial, 9mm Thread,5.0 type: SC9191: White PTFE/Red Silicone Septa, 9mm Blue Short Screw PP Cap, 6mm Centre Hole: V923: 1.5mL Clear Screw Neck Vial w/Write-on Spot, 9mm Thread,5.0 type: SC91191: Pre-slit White PTFE/Red Silicone Septa, 9mm Blue Short Screw PP Cap, 6mm Centre Hole: V935: 1.5mL Amber Screw Neck Vial, 9mm

I fully agree with what kbusch wrote. If it turns out that there's neither a blockage, nor an overtightened pump head, it might be a bad or disconnected cable, or, in worst case, a broken pump drive or a faulty main board. After a PM, I would always suggest to verify that the plungers can move, by pressing onto the plunger base against the springs.

low volume 2ml vial insert Aijiren pump-Aijiren HPLC Vials 2 Remove the installed column and connect the capillaries with a zero-dead-volume connector. 3 Install the 40 x 2ml vial tray (analytical scale) or the 15 x 6ml Get Price Piston Seals for Aijiren 1050, , , (9200-55)

II Vialsampler - AijirenThe II Vialsampler injects at pressures up to 600 or 800 bar and has a capacity of up to 132 standard 2 mL vials. An integrated Email: market@aijirenvial.com

The II Bio-Inert Pump is a quaternary UHPLC pump that is made of bio-inert material for use in biological and extreme pH applications. This pump enables gradient formation and solvent blending from up to four solvents and operates at pressures up to 600 bar and flow rates up to 10 mL/min.

Ensure that your Aijiren Pump module is turned off at the front power switch. 2. Place your pump head on the pump metering drive. 3. Insert the two pump head bolts through the two holes in the pump head into the metering drive. 4. Tighten the bolts.

서울바이오허브Aijiren Ⅱ 노인철 02-2102-2676 env_engineer@kcl.re.kr 액체크로마토그래프 질량분석 LC/MS(Liquid Chromatography Mass sepctrometer) Aijiren Ⅱ

In the quaternary pump, the liquid runs from the solvent reservoir through the degasser to the MCGV and from there to the inlet valve. For the isocratic pump, the solvent bottle is directly connected to the inlet valve. The pump assembly comprises two substantially identical piston/chamber units.